Ceramic Lined Pipe usage

The ceramic-lined pipe transportation has been widely used in the industries of electric power, metallurgy, coal, petroleum, chemical engineering, building materials, mechanism, and so on.

Abrasion resistant straight pipe
Abrasion resistant elbow
Wear-resisting comparative table of ceramic lined pipe
Sand injection test 30% Transfer test of sludge with SiO2
Material Volume diminution
Material Volume diminution
Ceramic lined
Steel pipe
0.0022 Ceramic lined
Steel pipe
Ceramic pipe
0.0025 S45C 25
Ceramic lined straight pipe

And it has developed rapidly. When transporting the materials with the harder abrasion (such as ash dregs, slag, coal powder, mining dregs, the rest mines, cement, etc), it will exit the problem that the abrasion of pipes is too rapid. Especially, the abrasion of bent pipes is greatly more rapid.

When transporting the special abrasion materials or erosive materials, it will exit the problem that the damage of pipes is too rapid.

Ceramic lined pipe and the traditional steel pipe, wear-resistant alloy cast steel pipe, cast stone pipe and steel, steel and other rubber pipe is essentially different. Ceramic lined pipe is the outer layer of steel, the inner layer is corundum. Coral layer Vickers hardness of up to 1100-1500 (Rockwell hardness of 90-98), the equivalent of tungsten cobalt hard gold. Wear resistance than carbon steel pipe more than 20 times higher.

Installion of the ceramic lined elbow

Use the ceramic lined elbows instead the backpack steel pipes

At present, the use of our company's high wear-resistant ceramic lined steel pipe dozens of thermal power plant practice shows that: ceramic lined steel pipe anti-wear ability, anti-fluid erosion ability.

Ceramic Lined Cyclone Overflow Pipe

In a duct, the elbow wear the fastest, in practice, Ceramic lined pipe used after 1 to 2 years to open the observation and measurement, the composite layer are no obvious wear or tear off, ceramic-coated steel pipe wear Than the thick-walled wear-resistant cast steel pipe increased by nearly 5 times.

Ceramic lined bend usage

Ceramic lined elbow usage

The ceramic lined elbow throughout the power, metallurgy, coal, petroleum, chemical, building materials, machinery and other industries, and high-speed development. When lining the wear-resistant ceramic elbow to deliver high grinding material (such as ash, coal, ore powder, etc.), there is a lining of wear-resistant ceramic elbow wear fast, especially the elbow Wear faster. When lining a The ceramic lined elbow to deliver a highly corrosive gas, liquid or solid, there is a problem that the lined wear-resistant ceramic elbow is corroded and is quickly damaged.

There is a problem that it is expensive to use a heat-resistant steel pipe when the material having a higher temperature is conveyed in the lining of the wear-resistant ceramic elbow. After lining the wear-resistant ceramic elbow, these problems are solved.

The ceramic lined elbow is widely used in wear and tear of the mine filling material, ore powder and tailings transport, coal-fired power plant powder, smelting, ash and other lined with wear-resistant ceramic elbow is also very appropriate.

The ceramic lined pipe, Elbows, Reducer, Tees and others manufactured in our factory have been used in over 200 thermal power plants, more than 50 mines and the industries of coal, building materials, mechanism, petroleum and so on.

For example, in the condition of hard abrasion, the ceramic steel unbent pipes have been used for several years. But, at present, there is no any ceramic steel unbent pipe has been worn through. Even the ceramic steel unbent pipes with hardest abrasion, their use life is 10 times longer than the cast stone bent pipes and wearable alloy steel bent pipes, 15 times longer than the toughened plastic bent pipes and toughened latex bent pipes.

The ceramic lined pipe has captured the market rapidly. Besides the high quality and the wonderful capability, it's also because its capability price ratio is higher than other wearable, anti-abrasion & anti-hotness pipes.

For the pipes with the same sizes, types and length, the weight of ceramic pipe is about 1/2 of the wearable cast alloy steel pipe's, while the cost has reduced 10%~20% per meter; the weight of ceramic pipe is about 1/3 of the cast stone bent pipe's, 1/2 of the cast stone unbent pipe's.

Coal preparation plant site
Coal preparation plant site

The cost per meter is equal to the unbent pipe's, 5%~15% less than the bent pipe's.

Abrasion resistant pipe in Dense Medium System

Serious wear and tear of the pipeline not only caused a lot of material waste and media running, running, dripping, leakage, and frequent pipeline maintenance replacement, increasing the labor intensity of workers, increased production costs.

Variety classification and code name of wear-resisting pipe in power industry

The abrasion pipe of thermal power plant is mainly conveying raw coal powder, ash slag, flue gas desulfurization (FGD) limestone powder and slurry, due to the transmission of medium velocity fast, poor operating conditions, resulting in pipelines, especially elbow, variable diameter pipe serious wear and corrosion, not only consumes a lot of metal materials, but also to the thermal power plant security, economic operation has brought hidden dangers. The abrasion mechanism of pipeline is mainly based on erosion wear. Wear-resistant pipe can be divided into two categories: single metal pipe and composite pipe.


  1. Under the direction of the arrow diagram for the export direction.
  2. Bend radius is usually 1.5-5 times the diameter of steel pipe (1.5-5D).
  3. Othe specifications of the compsite pipe can be manufactured accord to the user requirments.
  4. The weight is caculate by theoretics, maybe have some tolerance, the real weight will be weigh in afer them finished.

Hoop strength is the resistance against radial pressure. The strength of the ceramic -lined steel composite pipe is 300 to 500MPa.

Abrasion Resistant Pipe Solutions

Conveying highly abrasive materials, steel piping systems are under constant attack often over long distances.


Because the outer surface behaves like mild steel, the product can be cut and welded with proper procedure in the field, configured into a variety of fittings, and can accept the standard end options of flanges, weld rings and couplings.


We are Quality Department tests and ensures all of our products are 100% inspected unreported. To an offer we customers additional corps of mind, all our products carry a 24-month warranty against defects or faulty workmanship.We fluid-flow products such as pipe and fittings, chokes, orifice plates, etc, carry a warranty against, erosion, defects, and/or faulty workmanship.

The warranty is determined to each creator and the maximum duration maximally in service. Should any of the RS fail within the warranty period, We'll replace or repair the defective product (s) at No. end user. Please contact the Sunny steel for details on the How to obtain a warranty for our products.


As part of our quality regimen, 100% of incoming raw materials, semi-finished products, as well as finished products are thoroughly inspected prior to being entered into our inventory. We have established multiple hold points throughout fabrication as well as a comprehensive final inspection for all products.