ASTM A213 T5 Seamless alloy pipe

ASTM A213 T5 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.

ASTM A213 T5

Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

Sunny Steel offers outside diameters of 5/8″ through 1-1/2″, wall thicknesses from .049″ through .135″ and lengths from 6 feet to 60′ long. Please inquire about our bending and finning capabilities.

ASTM A213 T5

ASTM A209 Through A213

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Chemical Composition(%) for ASTM A213 T5 Low Alloy Steel

UNS Designation K41545
Carbon 0.05
Manganese 0.30–0.60
Phosphorus 0.025
Sulfur 0.025
Silicon 0.50
Nickel
Chromium 4.00-6.00
Molybdenum 0.15-0.65
Vanadium
Boron
Niobium
Nitrogen
Aluminum
Tungsten
Other Elements

Mechanical properties for ASTM A213 T5 Low Alloy Steel

Tensile strength(min) 415Mpa
Yield strength(min) 220Mpa
Elongation 30%
Delivery condition annealed

Equivalent Designation

DIN EN BS NFA ASTM ASME
DIN Wbl- 007/2* Grade 12 CrMo 19 5 EN X11CrMo5 Grade 10216 – 2 – – ASTM A213 Grade T5 ASME SA 213 Grade T5 UNI 17102
ASTM A213 Standard Scope

1.1 This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T91, TP304, etc. These steels are listed in Tables 1 and 2.
1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements.
1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
TABLE 1 Chemical Composition Limits, %A, for Low Alloy SteelA Maximum, unless range or minimum is indicated. Where ellipses (…) appear in this table, there is no requirement, and analysis for the element need not be determined or reported.

B It is permissible to order T2 and T12 with a sulfur content of 0.045 max. See 16.3.

C Alternatively, in lieu of this ratio minimum, the material shall have a minimum hardness of 275 HV in the hardened condition, defined as after austenitizing and cooling to room temperature but prior to tempering. Hardness testing shall be performed at mid-thickness of the product. Hardness test frequency shall be two samples of product per heat treatment lot and the hardness testing results shall be reported on the material test report.

Referenced Documents (purchase separately)

Other ASTM Standards

ASME SA 213 Grade T5 Alloy Steel Seamless Tubes are minimum-wall-thickness, seamless ferritic and austenitic steel, boiler and superheater tubes and austenitic steel heat-exchanger tubes, designated Grades T5, T11,T22,T91 etc. The tubing sizes and thicknesses usually furnished to ASME SA 213 Grade T5 specification are 1-8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness. SA 213 Tubes having other dimensions may be furnished & provided such tubes comply with all other requirements of this specification.

Wall Thickness : the minimum wall thickness at any point or end on ASME SA 213 pipes and tubes shall not be greater than 12.5% under the nominal thickness specified.

Inner Diameter: For pipe ordered in inside diameter, the inside diameter shall not vary more than ñ 1% from the required/specified inside diameter.

ASTM A213 T5 Superheater and Heat-Exchanger Tubes
A213 T5 Superheater Tubes
ASTM A213 T5 Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes.
Measurment out diameter
ASTM A213 T5b alloy tube
ASTM A213 T5b Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes.
ASTM A213 T9
ASTM A213 T9 alloy pipe
ASTM A213 T9 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Heat-Exchanger Tubes.
ASTM A213 T11
ASTM A213 T11 alloy pipe
ASTM A213 T91 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified.
ASTM A213 T91
ASTM A213 T91 alloy tube
ASTM A213 T91 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.
ASTM A213 T22
ASTM A213 T22 alloy pipes
ASTM A213 T22 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.

Standards for Alloy pipes & tubes

ASTM A213 T91
ASTM A213M-09
Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
ASTM A333 Grade 6 alloy pipe shall be made by the seamless or welding process with the addition of no filler metal in the welding operation.
ASTM A333
Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications.
ASTM A335 P22 is the part of ASTM A335, the pipe shall be suitable for bending, flanging, and similar forming operations, and for fusion welding.
ASTM A335
ASTM A335/ASME SA335 standard specication for seamless ferritic alloy-steel pipe for high-temperature service
Related alloy steel products:
Carbon steel flanges
Alloy steel flanges
Alloy steel flange, that is, the main material is alloy steel flange or end flange connectors. It contains alloy steel flange, known as alloy steel flange.
Rare earth alloy wear-resistant tube
Rare earth alloy wear resistant pipe has the characteristics of fast velocity and high flow rate is used for pneumatic, pump slurry, etc.
Wear resistant alloy composite pipe
Wear resistant alloy composite pipe
Wear-resistant alloy steel pipe as the base, lined with ultra-wear-resistant alloy, through the centrifugal casting, metallurgy combined to form a solid.

Alloy steel specification, Standard and identification

Alloy Steel pipe contains substantial quantities of elements other than carbon such as nickel, chromium, silicon, manganese, tungsten, molybdenum, vanadium and limited amounts of other commonly accepted elements such as manganese, sulfur, silicon, and phosphorous.

ASTM A519-89 Standard specification

ASTM A519- specification covers for several grades of carbon and alloy steel mechanical tubing, either hot-finished or cold-finished.

EN10216 Standard specification

EN 10216 is a European standard suitable for seamless steel tubes for pressure purposes.

EN 10216 non alloy steel tubes EN 10216 non alloy steel tubes

The main steel grade:
  • P195GH, P235GH, P265GH, 13CrMo4-5, 10CrMo9-10
  • Other grades of steel pipe can be provided based on negotiations.

Industries We Serve

Our team of experienced sales specialists proudly partners with gas and chemical processors, power generation plants, oil refineries, and related industries to offer piping components and value-added services.

ASTM A335 P11 alloy pipe


SUNNY STEEL

Our team are highly trained and experienced in servicing and producing all types of steel supplies. Whether you've got a large construction project, or need parts for industrial machinery, our team of steel fabrication consultants will ensure that your project is provided with the parts you need, when you need them.

Link exchange

Copyright © 2011 Sunny Steel Enterprise Ltd.  All Rights Reserved ICP No.:08010763